DOI: 10.5937/jaes0-31703
This is an open access article distributed under the CC BY 4.0
Volume 20 article 908 pages: 91-100
The unbalance moments at the edge connections of flat plate structures induced by lateral forces (i.e. an earthquake) may not always act in parallel directions of the building axes. Most research studied the unbalanced moments in one direction, a few of them in biaxial directions, and none of them in incline directions. This paper presents the results of a nonlinear finite element analysis on punching shear capacity at edge column-slab connections subjected to three directions of the unbalanced moments namely perpendicular, incline 45°, and parallel to the slab free edge in combination with the shear force. A 3-D numerical analysis of ten isolated edge column-plate connections was conducted by applying an appropriate element size, mesh, and calibrated material parameters of the concrete damage plasticity (CDP) model in ABAQUS. the connections were subjected to ten variations of the moment to shear (M/V) ratios. The results show that the punching shear capacity decreases exponentially for the unbalanced moment acting perpendicular and parallel to the slab free edge, and linearly for unbalanced moment incline 45° as the increase in M/V ratio. The M-V interaction at the edge connections depends on the unbalanced moment directions which are slightly different from the ACI 318 code.
1. ACI Committee 318 (2019) Building Code Requirements for Structural Concrete and Commentary (ACI 318M-19). Farmington Hills
2. Widianto, Bayrak O, Jirsa JO (2009) Two-Way Shear Strenght of Slab-Column Connections: Reexamination of ACI 318 Provisions. ACI Structural Journal 106:160 – 170
3. Moehle JP (1988) Strength of Slab-Column Edge Connection. ACI Structural Journal 85:89–98
4. Matzke EM, Lequesne RD, Parra-montesinos GJ, Shield CK (2015) Behavior of Biaxially Loaded Slab-Column Connections with Shear Studs. ACI Structural Journal 112:335–346. https://doi.org/10.14359/51687408
5. Kang SM, Na SJ, Hwang HJ (2021) Two-way shear strength of reinforced concrete transfer slab-column connections. Engineering Structures 231:2020–2021. https://doi.org/10.1016/j.engstruct.2020.111693
6. Milligan GJ, Polak MA, Zurell C (2020) Finite element analysis of punching shear behavior of concrete slabs supported on rectangular columns. Engineering Structures 224:111189. https://doi.org/10.1016/j.engstruct.2020.111189
7. Filatov VB, Galyautdinov ZS, Blinkova E V., Zhiltsov YV (2020) Numerical study of stress-strain state of reinforced concrete slab in punching zone. IOP Conference Series: Materials Science and Engineering 775:7–11. https://doi.org/10.1088/1757-899X/775/1/012136
8. Bompa D V., Elghazouli AY (2020) Nonlinear numerical simulation of punching shear behavior of reinforced concrete flat slabs with shear-heads. Frontiers of Structural and Civil Engineering 14:331–356. https://doi.org/10.1007/s11709-019-0596-5
9. Genikomsou AS, Polak MA (2015) Finite element analysis of punching shear of concrete slabs using damaged plasticity model in ABAQUS. Engineering Structures 98:38–48. https://doi.org/10.1016/j.engstruct.2015.04.016
10. Abdul Rasoul ZMR, Taher HMAM (2019) Accuracy of concrete strength prediction behavior in simulating punching shear behavior of flat slab using finite element approach in abaqus. Periodicals of Engineering and Natural Sciences 7:1933–1949. https://doi.org/10.21533/pen.v7i4.943
11. Boonpichetvong M, Pannachet T, Pinitkarnwatkul S (2016) Finite element modeling of concrete specimens confined with metal sheet strips. International Journal of Technology 7:1132–1140. https://doi.org/10.14716/ijtech.v7i7.4875
12. Moehle JP (1988) Strength of Slab-Column Edge Connections. ACI Structural Journal 85:89–98
13. Badan Standarisasi Nasional (2019) SNI 2847:2019 Persyaratan beton struktural untuk bangunan gedung dan penjelasan. Jakarta
14. Badan Standardisasi Nasional (2019) SNI-1726:2019 Tata Cara perencanaan ketahanan gempa untuk struktur bangunan gedung dan non gedung. Jakarta
15. Wiryadi IGG (2017) Analisis elemen hingga perilaku hubungan pelat-kolom beton bertulang akibat gaya geser dan momen tak imbang dua arah. Udayana University
16. Hognestad E (1951) A Study of Combined Bending and Axial Load in Reinforced Concrete Members. University of Illinois Bulletin Series 399:49. https://doi.org/10.14359/7785
17. Lubliner J, Oliver J, Oller S, Oñate E (1989) A plastic-damage model for concrete. International Journal of Solids and Structures. https://doi.org/10.1016/0020-7683(89)90050-4
18. Lee J, Fenves GL (1998) Plastic-damage model for cyclic loading of concrete structures. Journal of Engineering Mechanics 124:892–900
19. Wosatko A, Genikomsou A, Pamin J, et al (2018) Examination of two regularized damage-plasticity models for concrete with regard to crack closing. Engineering Fracture Mechanics. https://doi.org/10.1016/j.engfracmech.2018.03.002
20. Tambusay A, Suprobo P, Faimun, Amiruddin AA (2016) Analyses Behavior of Slab-Column Connections Using ECC Material Based. EASEC 14.: https://doi.org/10.13140/RG.2.1.1517.7367
21. Qingfu L, Wei G, Yihang K (2020) Parameter calculation and verification of concrete plastic damage model of ABAQUS. In: IOP Conference Series: Materials Science and Engineering. Institute of Physics Publishing
22. El-salakawy EF, Polak MA, Soliman MH (1998) Slab-column edge connections subjected to high moments. Can J Civ Eng 25:526–538
23. Sudarsana IK, Gegiranang Wiryadi IG, Adi Susila IG (2017) Analisis Perilaku Hubungan Pelat-Kolom Tepi Struktur Pelat Datar menggunakan Concrete Damage Plasticity (CDP) dalam Abaqus. Jurnal Spektran 5:
24. Viswanathan TS, Mohan GG, Santhi AS (2012) Shear stress distribution of flat-plate using Finite Element Analysis. International Journal of Civil and Structural Engineering 2.: https://doi.org/10.6088/ijcser.00202030019
25. Comite Euro-International du Beton (2013) CEB-FIP Model Code for Concrete Structures 2010. Ernst & Sohn, Berlin
26. Gardner NJ, Shao XY (1996) Punching Shear of Continuous Flat Reinforced Concrete Slabs. ACI Structural Journal 93:218 – 228
27. Sudarsana IK (2001) Punching Shear in Edge and Corner Column Slab Connections of Flat Plate Structures. University of Ottawa
28. Sherif AG, Dilger WH (1966) Critical Review of the CSA A23.3-94 Punching Shear Strength Provision for Interior Columns. Canadian Journal for Civil Engineering 23:998–1011