EFFECT OF GAS NITRIDing PARAMETERS ON THE MICRO-HARDNESS OF HIGH-SPEED STEEL-CUTTing TOOLS
Abstract
In this study, the nitriding parameters, such as nitriding time, nitrogen flow, and cooling type, were regularly modified to assess the effects of each on the microhardness of tools constructed of high-speed steel designed for commercial usage. The nitriding temperature was maintained at 670 °С for all of the tools. The tools were designed to measure microhardness. With a maximum value of 2000 HV at a time of 42 hours, direct nitriding with a nitrogen flow of 20 l/h and air cooling exhibits an apparent relationship between nitriding time and microhardness. The maximum microhardness value (1555.44 HV) was achieved by quenching after nitriding for 72 hours with a nitrogen flow rate of 20 l/h. The relationship between nitrogen flow and microhardness is semi-direct for direct nitriding at a nitriding duration of 30 hours and furnace cooling, with a maximum value of 1566.65 HV at a nitrogen flow of 110 l/h. The maximum microhardness was 2000 HV, with a 1.63% increase. The microstructure of the tools was improved by increasing the concentration of iron nitride in the ferrite cell, which means that the gas nitriding process increases the efficiency of cutting operations and reduces workpiece material surface roughness, based on the results of this study, it is advised to use high-purity nitrogen rather than ammonia. high-purity nitrogen gives better results than traditional nitriding using ammonia gas.
Keywords
Acknowledgements
We gratefully acknowledge the support provided by Mutah University.
References
1. Özel, T., & Karpat, Y. (2005). Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks. International journal of machine tools and manufacture, 45(4-5), 467-479. https://doi.org/10.1016/j.ijmachtools.2004.09.007
2. Ezugwu, E. O. (2005). Key improvements in the machining of difficult-to-cut aerospace superalloys. International Journal of Machine Tools and Manufacture, 45(12-13), 1353-1367. https://doi.org/10.1016/j.ijmachtools.2005.02.003
3. Akhtar, S. S.&, Arif, A. (2010). Evaluation of gas nitriding process with in-process variation of nitriding potential for AISI H13 tool steel. The International Journal of Advanced Manufacturing Technology, 47, 687-698. DOI 10.1007/s00170-009-2215-4
4. Şirin, Ş. &, Sarıkaya, M., (2021). Machinability performance of nickel alloy X-750 with SiAlON ceramic cutting tool under dry, MQL and hBN mixed nanofluid-MQL. Tribology International, 153, 106673. https://doi.org/10.1016/j.triboint.2020.106673
5. Da Silva Savonov, & G., Camarinha, (2019). Study of the influence of the RRA thermal treatment and plasma nitriding on corrosion behavior of 7075-T6 aluminum alloy. Surface and Coatings Technology, 374, 736-744. https://doi.org/10.1016/j.surfcoat.2019.04.095
6. Fu, Y., & Liao, Y. (2022). Layer structured materials for ambient nitrogen fixation. Coordination Chemistry Reviews, 460, 214468. https://doi.org/10.1016/j.ccr.2022.214468
7. Wang, L., & Chen, W. (2019). Surface strategies for catalytic CO 2 reduction: from two-dimensional materials to nanoclusters to single atoms. Chemical Society Reviews, 48(21), 5310-5349 https://doi.org/10.1039/C9CS00163H
8. Tu, L, &Tian, S. (2020). Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron. Journal of manufacturing processes, 56, 158-168. https://doi.org/10.1016/j.jmapro.2020.04.081
9. Özel, T.&, Biermann, D. (2021). Structured and textured cutting tool surfaces for machining applications. CIRP Annals, 70(2), 495-518. https://doi.org/10.1016/j.cirp.2021.05.006
10. Fouathiya A, Meziani S, Sahli M, Barrière T. (2021) Experimental investigation of microtextured cutting tool performance in titanium alloy via turning. Journal of Manufacturing Processes.;69:33-46. https://doi.org/10.1016/j.jmapro.2021.07.030
11. Gordon, S.& Lahiff, C. (2019). The Effect of High-Speed Machining on the Crater Wear Behaviour of PCBN Tools in Hard Turning. Procedia Manufacturing, 38, 1833-1848. https://doi.org/10.1016/j.promfg.2020.01.076
12. Dolinšek S, Šuštaršič B, Kopač J. (2001) Wear mechanisms of cutting tools in high-speed cutting processes. Wear.;250(1-12):349-56. https://doi.org/10.1016/S0043-1648(01)00620-2
13. Cheng, Y.&, Ding, Y. (2022). Simulation and experimental study of tool wear and damage in milling SA 508III steel. Surface Topography: Metrology and Properties, 10(3), 035033. DOI 10.1088/2051-672X/ac9073
14. Sarıkaya, M., & Gupta, M. K. (2021). A state-of-the-art review on tool wear and surface integrity characteristics in machining of superalloys. CIRP Journal of Manufacturing Science and Technology, 35, 624-658. https://doi.org/10.1016/j.cirpj.2021.08.005
15. Szczotkarz, N., & Mrugalski, R. (2021). Cutting tool wear in turning 316L stainless steel in the conditions of minimized lubrication. Tribology International, 156, 106813. https://doi.org/10.1016/j.triboint.2020.106813
16. de Araújo, E., Bandeira, R. M., Manfrinato, M. D., Moreto, J. A., Borges, R., dos Santos Vales, S., Suzuki, P. A., & Rossino, L. S. (2019). Effect of ionic plasma nitriding process on the corrosion and micro-abrasive wear behavior of AISI 316L austenitic and AISI 470 super-ferritic stainless steels. Journal of Materials Research and Technology, 8(2), 2180-2191. https://doi.org/10.1016/j.jmrt.2019.02.006
17. Fu, Y., & Liao, Y. (2022). Layer structured materials for ambient nitrogen fixation. Coordination Chemistry Reviews, 460, 214468. https://doi.org/10.1016/j.ccr.2022.214468
18. Venkatesan, K., Devendiran, S. (2020). Investigation of machinability characteristics and comparative analysis under different machining conditions for sustainable manufacturing. Measurement, 154, 107425. https://doi.org/10.1016/j.measurement.2019.107425 .
19. Bloyce, A. (1998). Surface engineering of titanium alloys for wear protection. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 212(6), 467-476. https://doi.org/10.1243/1350650981542263
20. Şap, E., Usca, U. A. (2021). Tool wear and machinability investigations in dry turning of Cu/Mo-SiCp hybrid composites. The International Journal of Advanced Manufacturing Technology, 114(1), 379-396. https://doi.org/10.1007/s00170-021-06889-8
21. Xu, Z., Huang, J., Xu. (2020). Plasma surface metallurgy of materials based on double glow discharge phenomenon. arXiv preprint arXiv:2003.10250. https://doi.org/10.48550/arXiv.2003.10250
22. Chiang, W. H., Mariotti, D. (2020). Microplasmas for advanced materials and devices. Advanced Materials, 32(18), 1905508. https://doi.org/10.1002/adma.201905508
23. Eng, A. Y. S., Kumar, V., Zhang, Y., Luo, J., Wang, W., Sun, Y., Li, W., & Seh, Z. W. (2021). Room-temperature sodium–sulfur batteries and beyond: Realizing practical high energy systems through anode, cathode, and electrolyte engineering. Advanced Energy Materials, 11(14), 2003493. https://doi.org/10.1002/aenm.202003493
24. Cojocaru. M. O., Branzei, M. (2021). Sulfonitrocarburizing of High-Speed Steel Cutting Tools: Kinetics and Performances. Materials, 14(24), 7779. https://doi.org/10.3390/ma14247779
25. Fouathiya, A., Meziani, S. (2021). Experimental investigation of microtextured cutting tool performance in titanium alloy via turning. Journal of Manufacturing Processes, 69, 33-46. https://doi.org/10.1016/j.jmapro.2021.07.030
26. Günay, M., Korkmaz, M. (2020). Performance analysis of coated carbide tool in turning of Nimonic 80A superalloy under different cutting environments. Journal of Manufacturing Processes, 56, 678-687. . https://doi.org/10.1016/j.jmapro.2020.05.031
27. Astakhov, V. P. (2004). The assessment of cutting tool wear. International journal of machine tools and manufacture, 44(6), 637-647. https://doi.org/10.3390/pr8091056
28. Evseev, N., Ziatdinov, M. (2020). Process of obtaining chromium nitride in the combustion mode under conditions of co-flow filtration. Processes, 8(9), 1056. https://doi.org/10.3390/pr8091056
29. Rath, D., & Panda, S. (2022). Analysis and prediction of tool wear in dry turning of hardened D3 steel using hybrid insert: A novel wear map approach. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 236(10), 1355-1367. https://doi.org/10.1177/09544054221076242
30. Poulachon, G., Moisan, A. (2001). Tool-wear mechanisms in hard turning with polycrystalline cubic boron nitride tools. Wear, 250(1-12), 576-586. https://doi.org/10.1016/S0043-1648(01)00609-3